Zelmer 39Z017 User Manual download pdf (Page 28)

28 GW39-008_v01

Outline and parts of the hair clipper (Fig. A)

Cutting head

Cutting length adjustment knob

On/OFF switch

LCD display

Battery rechargeable

Loading socket

Attachments (4-6; 10-12; 16-18; 22-24; 28-30 mm)

Power supply

Cleaning brush

Lubricating oil for blades

Comb

Scissors

LCD display

percentage charging level indicator

graphical battery charging level indicator

mains supply connection indicator

Handling and operation of hair clipper

OPERATION WITH POWER SUPPLY ADAPTOR

At rst insert the adaptor plug into the device and then

insert the adapter plug into the mains supply outlet (230 V).

In mains supplied mode the device is ready for use.

LOADING ACCUMULATORS AND CORDLESS

OPERATION

Load the device minimum 16h before rst usage and

when 2–3 next loadings.

Make sure the appliance is switched off before charging.

●

The process of battery (installed in the trimmer) charging

●

lasts approximately 2 hours.

The trimmer can work approx. 60 minutes with fully

●

charged batteries.

Insert the ending of the power supply to the trimmer –

charging socket (6),

Insert the plug of the power supply in the mains –

supply outlet. The percentage and graphical

charging level indicators show the charging process

advancement (ashing).

When the battery is fully charged, the LCD display

●

(4)

indicates 100 and it is highlighted in blue.

When the battery charging level decreases below 20, the

●

graphical battery charging level indicator (B) and mains

supply connection indicator (C) start ashing.

When the battery is almost empty, the display colour

●

changes into red. Connect the trimmer to the mains supply.

The hair clipper accumulator obtains optimum power

●

after three cycles of loading and unloading. Ten hours

is enough for next loading. In order to provide long life

of accumulators, they should be completely unloaded

before loading.

COMB ATTACHMENTS INSERTING / REPLACING

Select the attachment according to the length of cutting.

●

Insert appropriate attachment into the sides of the device.

●

The protrusions shall be locked inside small holes (see

the gure beside) on left and right sides.

Replace one attachment removing it and inserting

●

another as described above.

In order to remove an attachment bent one side of assembled

attachment gently and then move it up.

Move the cutting length adjustment knob

●

(2), to increase/

reduce the hair cutting length. The possible hair cutting

length is indicated on each attachment (i.e. 4–6 mm).

USING THE TRIMMER FOR HEAR CUTTING

Cut the hair for demanded length in stages, start form

bigger length.

Insert an appropriate attachment

●

(7).

Set the desired length of hair/beard cutting with cutting

●

length adjustment knob (2).

Start up the hair clipper pressing in ON/OFF button

●

(3).

Cut only small areas.

●

Move the clipper slowly along hair.

●

Hold the device so, that the comb attachment is laid at.

●

Always start the cutting from the neck upwards or from

●

the forehead and temples upwards to the top of head.

CUTTING HAIR WITHOUT ATTACHMENT

WARNING: The cutting head (1) is very sharp. Injury

hazard!

Cutting without attachment makes possible to trim the

contour, hair line and whiskers as well as neck shaving.

Turn the device so, that the back part was directed

●

upwards.

Place the edge of the cutting head

●

(1) without comb

attachment on desired length of bristle hairline.

Move down the clipper in operation.

●

Cleaning and maintenance

Start the device pressing in ON/OFF button

●

(3).

Always switch off the hair clipper and unplug the adaptor

●

from the mains supply outlet before cleaning and

maintenance.

Remove the comb attachment from the hair clipper.

●

In order to remove cutting head press the cutting head

●

blade (1) forward with your thumb, in order to release it

from the frame (Fig. C).

If necessary, rinse the plastic comb attachments under

●

running water, and then dry them thoroughly.

Remove the remains of hair from the cutting head

●

(1)

with attached cleaning brush (VII).

Insert the protrusion of cutting head

●

(1) back into the

locking hole in the frame of cutting head.

Press gently the cutting head

●

(1) in, until you hear

a clicking sound of locking.

1 2 ... 23 24 25 26 27 28 29 30 31 32

Comments to this Manuals

No comments

Zelmer 39Z017 User Manual Page 28

Comments to this Manuals

Related products and manuals for Hair clippers Zelmer 39Z017